10000W Peak 30000W Pure Sine Wave Power Inverter Split Phase DC 24V AC Input 240V AC Output 120V and 240V Converter 60A MPPT Solar Charger Controller, Utility Transfer SW Inverter Charger Solar Power

*SP-PV Series Pure Sine Wave Inverter is a combination of an inverter, AC charger, Mppt solar charger and Auto-transfer switch into one complete system.It is packed with unique features and it is one of the most advanced inverter/chargers in the market today
*Our Low Frequency Inverter is designed with AC priority by default. This means, when AC input is present, the battery will be charged first, and the inverter will transfer the input AC to power the load.The AC Priority and Battery Priority switch is SW4.When you choose battery priority, the inverter will inverting from battery despite the AC input
*SP-PV Series Inverter is equipped with a powerful charger of up to 120Amp (depending on Model).The overload capacity is 300% of continuous output for up to 20 seconds to reliably support tools and equipment longer. the max chargecurrent can be adjusted from 0%-100% via a liner switch at the right of the battery type selector.This will be helpful if you are using our powerful charger on a small capacity battery bank

General specification:

Continuous Output Power :10.0KW
Surge Rating(20s) :30.0KW
Output Waveform :Pure Sine Wave
AC Output Voltage:120V and 240V
AC Input Voltage:240Vac
DC Battery Voltage:24Vdc
Solar charger Current:60Amp
AC Battery charger:120±5Amp
Output Voltage Regulation :±10% RMS
Output Frequency :50Hz ± 0.3Hz /60Hz ± 0.3Hz
Typical transfer Time :10ms(Max)

DC Input:

Nominal Input Voltage :24.0Vdc
Minimum Start Voltage :20.0Vdc
Low Battery Alarm :21.0Vdc / 22.0Vdc
Low Battery Go back and forth :20.0Vdc / 21.0Vdc
High Voltage Alarm :32.0Vdc
Low Battery voltage get better :31.0Vdc
Idle Consumption-Search Mode :<25 W when Power Saver On Charger:

Output Voltage: Depends upon battery type
Max Charge Power Rate: 1/3 Rating Power
Battery Initial Voltage for Start Up: 20-31.4V
Over Charge Protection Shutdown :31.4V
Remote Keep watch over :Yes

Bypass & Protection:

Input Voltage Waveform :Sine wave (Grid or Generator)
Nominal Voltage:230Vac
Nominal Input Frequency :50Hz or 60Hz
Bypass breaker rating: 50A

Solar Charger controller:

Rated Voltage :24Vdc
Solar Input Voltage Range: 30-70Vdc
Max.PV Open Circuit Array Voltage:105Vdc
Rated Charge Current :60A
Over Charge Disconnection: 29.6V
Over Charge Recovery :27.2V
Over Discharge Disconnection:21.6V
Over Discharge Reconnection :24.6V

Mechanical specification:

Inverter Dimensions(L*W*H) :588*415*200mm
Inverter Weight(Solar Chg)KG: 80
Display :LED +LCD
Standard Warranty :1 Year
*SP-PV Series Pure Sine Wave Inverter is a combination of an inverter, AC charger, Mppt solar charger and Auto-transfer switch into one complete system.It’s packed with unique features and it is likely one of the such a lot advanced inverter/chargers available in the market as of late
*Our Low Frequency Inverter is designed with AC priority by default. This implies, when AC input is present, the battery shall be charged first, and the inverter will transfer the input AC to power the weight.The AC Priority and Battery Priority switch is SW4.When you select battery priority, the inverter will inverting from battery in spite of the AC input
*SP-PV Series Inverter is supplied with a powerful charger of as much as 120Amp (depending on Model).The overload capacity is three hundred% of constant output for as much as 20 seconds to reliably Strengthen tools and equipment longer. the max chargecurrent will also be adjusted from 0%-one hundred% by means of a liner switch on the right of the battery type selector.This shall be helpful in case you are the usage of our powerful charger on a small capacity battery bank
* Features: Low Frequency Inverter, Smart Remote Keep watch over, Automatic Generator Starting (AGS), Strengthen Solar Panel with MPPT Serve as. 8 pre Set Battery Type Selector plus De-sulphation for Totally Flat Batteries. 4-step Intelligent Battery Charging, PFC (Power Factor Correction) for Charger. 8 ms Typical Transfer Time Between Utility & Battery, Guarantees Power Continuity. 15s Delay Before Transfer when AC Resumes, Protection for Load when Used with Generator
*Applicantion:for all of the forms of load:circular saws,drills,grinders,sanders,buffers,weed and hedge trimmers, air compressors.computers,printers,monitors,facsimile machines, scanners.vacuum cleaners, fans, fluorescent and incandescent lighting,shavers, sewing machines.coffee makers, blenders,ice markers, toasters.metal halide lamp, high- pressure sodium lamp.tv, VCRs,video games, stereos,musical instruments, satellite equipment ect